darshan-runtime.txt 21 KB
Newer Older
1 2 3 4 5
Darshan-runtime installation and usage
======================================

== Introduction

6 7 8
This document describes darshan-runtime, which is the instrumentation
portion of the Darshan characterization tool.  It should be installed on the
system where you intend to collect I/O characterization information.
Philip Carns's avatar
Philip Carns committed
9

10 11 12
Darshan instruments applications via either compile time wrappers for static
executables or dynamic library preloading for dynamic executables.  An
application that has been instrumented with Darshan will produce a single
Kevin Harms's avatar
Kevin Harms committed
13
log file each time it is executed.  This log summarizes the I/O access patterns
14 15 16 17 18 19 20 21 22 23
used by the application.

The darshan-runtime instrumentation only instruments MPI applications (the
application must at least call `MPI_Init()` and `MPI_Finalize()`).  However,
it captures both MPI-IO and POSIX file access.  It also captures limited
information about HDF5 and PnetCDF access.

This document provides generic installation instructions, but "recipes" for
several common HPC systems are provided at the end of the document as well.

24 25 26
More information about Darshan can be found at the 
http://www.mcs.anl.gov/darshan[Darshan web site].

27 28 29 30 31
== Requirements

* MPI C compiler
* zlib development headers and library

Philip Carns's avatar
Philip Carns committed
32
== Compilation
33 34 35 36 37 38 39 40 41 42 43

.Configure and build example
----
tar -xvzf darshan-<version-number>.tar.gz
cd darshan-<version-number>/darshan-runtime
./configure --with-mem-align=8 --with-log-path=/darshan-logs --with-jobid-env=PBS_JOBID CC=mpicc
make
make install
----

.Explanation of configure arguments:
44
* `--with-mem-align=` (mandatory): This value is system-dependent and will be
45 46
used by Darshan to determine if the buffer for a read or write operation is
aligned in memory.
47
* `--with-jobid-env=` (mandatory): this specifies the environment variable that
48 49 50 51 52
Darshan should check to determine the jobid of a job.  Common values are
`PBS_JOBID` or `COBALT_JOBID`.  If you are not using a scheduler (or your
scheduler does not advertise the job ID) then you can specify `NONE` here.
Darshan will fall back to using the pid of the rank 0 process if the
specified environment variable is not set.
53 54 55 56
* `--with-log-path=` (this, or `--with-log-path-by-env`, is mandatory): This
specifies the parent directory for the directory tree where darshan logs
will be placed.
* `--with-log-path-by-env=`: specifies an environment variable to use to
57 58 59
determine the log path at run time.
* `--with-log-hints=`: specifies hints to use when writing the Darshan log
file.  See `./configure --help` for details.
60 61
* `--with-mod-mem=`: specifies the maximum amount of memory (in MiB) that
each Darshan module can consume.
62
* `--with-zlib=`: specifies an alternate location for the zlib development
Philip Carns's avatar
Philip Carns committed
63
header and library.
64 65 66 67 68 69 70
* `CC=`: specifies the MPI C compiler to use for compilation.
* `--disable-cuserid`: disables use of cuserid() at runtime.
* `--disable-ld-preload`: disables building of the Darshan LD_PRELOAD library
* `--disable-bgq-mod`: disables building of the BG/Q module (default checks
and only builds if BG/Q environment detected).
* `--enable-group-readable-logs`: sets darshan log file permissions to allow
group read access.
71 72 73

=== Cross compilation

Philip Carns's avatar
Philip Carns committed
74
On some systems (notably the IBM Blue Gene series), the login nodes do not
75 76
have the same architecture or runtime environment as the compute nodes.  In
this case, you must configure darshan-runtime to be built using a cross
Philip Carns's avatar
Philip Carns committed
77
compiler.  The following configure arguments show an example for the BG/P system:
78 79 80 81 82 83 84

----
--host=powerpc-bgp-linux CC=/bgsys/drivers/ppcfloor/comm/default/bin/mpicc 
----

== Environment preparation

Philip Carns's avatar
Philip Carns committed
85 86
Once darshan-runtime has been installed, you must prepare a location
in which to store the Darshan log files and configure an instrumentation method.
87 88 89

=== Log directory

90
This step can be safely skipped if you configured darshan-runtime using the
Philip Carns's avatar
Philip Carns committed
91 92
`--with-log-path-by-env` option.  A more typical configuration uses a static
directory hierarchy for Darshan log
93 94 95 96 97
files.

The `darshan-mk-log-dirs.pl` utility will configure the path specified at
configure time to include
subdirectories organized by year, month, and day in which log files will be
Philip Carns's avatar
Philip Carns committed
98
placed. The deepest subdirectories will have sticky permissions to enable
99 100 101 102 103 104 105
multiple users to write to the same directory.  If the log directory is
shared system-wide across many users then the following script should be run
as root.
 
----
darshan-mk-log-dirs.pl
----
106

107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125
.A note about log directory permissions
[NOTE]
====
All log files written by darshan have permissions set to only allow
read access by the owner of the file.  You can modify this behavior,
however, by specifying the --enable-group-readable-logs option at
configure time.  One notable deployment scenario would be to configure
Darshan and the log directories to allow all logs to be readable by both the
end user and a Darshan administrators group.   This can be done with the
following steps:

* set the --enable-group-readable-logs option at configure time
* create the log directories with darshan-mk-log-dirs.pl
* recursively set the group ownership of the log directories to the Darshan
administrators group
* recursively set the setgid bit on the log directories
====


126
=== Instrumentation method
127

128 129 130 131 132 133 134 135 136
The instrumentation method to use depends on whether the executables
produced by your MPI compiler are statically or dynamically linked.  If you
are unsure, you can check by running `ldd <executable_name>` on an example
executable.  Dynamically-linked executables will produce a list of shared
libraries when this command is executed.

Most MPI compilers allow you to toggle dynamic or static linking via options
such as `-dynamic` or `-static`.  Please check your MPI compiler man page
for details if you intend to force one mode or the other.
137 138 139

== Instrumenting statically-linked applications

140 141 142 143 144 145 146
Statically linked executables must be instrumented at compile time.
The simplest methods to do this are to either generate a customized
MPI compiler script (e.g. `mpicc`) that includes the link options and
libraries needed by Darshan, or to use existing profiling configuration
hooks for existing MPI compiler scripts.  Once this is done, Darshan
instrumentation is transparent; you simply compile applications using
the darshan-enabled MPI compiler scripts.
147

148 149
=== Using a profile configuration 

150
[[static-prof]]
151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180
The MPICH MPI implementation supports the specification of a profiling library
configuration, then it can be used to insert Darshan instrumentation without
modifying the existing MPI compiler script.  Example profiling configuration
files are installed with Darshan 2.3.1 and later.  You can enable a profiling
configuration using environment variables or command line arguments to the
compiler scripts:

Example for MPICH 3.1.1 or newer:
----
export MPICC_PROFILE=$DARSHAN_PREFIX/share/mpi-profile/darshan-cc
export MPICXX_PROFILE=$DARSHAN_PREFIX/share/mpi-profile/darshan-cxx
export MPIFORT_PROFILE=$DARSHAN_PREFIX/share/mpi-profile/darshan-f
----

Example for MPICH 3.1 or earlier:
----
export MPICC_PROFILE=$DARSHAN_PREFIX/share/mpi-profile/darshan-cc
export MPICXX_PROFILE=$DARSHAN_PREFIX/share/mpi-profile/darshan-cxx
export MPICF77_PROFILE=$DARSHAN_PREFIX/share/mpi-profile/darshan-f
export MPICF90_PROFILE=$DARSHAN_PREFIX/share/mpi-profile/darshan-f
----

Examples for command line use:
----
mpicc -profile=$DARSHAN_PREFIX/share/mpi-profile/darshan-c <args>
mpicxx -profile=$DARSHAN_PREFIX/share/mpi-profile/darshan-cxx <args>
mpif77 -profile=$DARSHAN_PREFIX/share/mpi-profile/darshan-f <args>
mpif90 -profile=$DARSHAN_PREFIX/share/mpi-profile/darshan-f <args>
----

181 182
=== Using customized compiler wrapper scripts

183
[[static-wrapper]]
184 185 186 187 188 189 190 191 192 193 194 195
For MPICH-based MPI libraries, such as MPICH1, MPICH2, or MVAPICH,
custom wrapper scripts can be generated to automatically include Darshan
instrumentation.  The following example illustrates how to produce
wrappers for C, C++, and Fortran compilers:

----
darshan-gen-cc.pl `which mpicc` --output mpicc.darshan
darshan-gen-cxx.pl `which mpicxx` --output mpicxx.darshan
darshan-gen-fortran.pl `which mpif77` --output mpif77.darshan
darshan-gen-fortran.pl `which mpif90` --output mpif90.darshan
-----

196 197
=== Other configurations

198 199 200
Please see the Cray recipe in this document for instructions on
instrumenting statically-linked applications on that platform.

201 202 203 204
For other MPI Libraries you must manually modify the MPI compiler scripts to
add the necessary link options and libraries.  Please see the
`darshan-gen-*` scripts for examples or contact the Darshan users mailing
list for help.
205 206 207

== Instrumenting dynamically-linked applications

208
For dynamically-linked executables, darshan relies on the `LD_PRELOAD`
Philip Carns's avatar
Philip Carns committed
209 210
environment variable to insert instrumentation at run time.  The executables
should be compiled using the normal, unmodified MPI compiler.
211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228

To use this mechanism, set the `LD_PRELOAD` environment variable to the full
path to the Darshan shared library, as in this example:

----
export LD_PRELOAD=/home/carns/darshan-install/lib/libdarshan.so
----

You can then run your application as usual.  Some environments may require a
special `mpirun` or `mpiexec` command line argument to propagate the
environment variable to all processes.  Other environments may require a
scheduler submission option to control this behavior.  Please check your
local site documentation for details.

=== Instrumenting dynamically-linked Fortran applications

Please follow the general steps outlined in the previous section.  For
Fortran applications compiled with MPICH you may have to take the additional
Philip Carns's avatar
Philip Carns committed
229
step of adding
230 231 232
`libfmpich.so` to your `LD_PRELOAD` environment variable. For example:

----
233
export LD_PRELOAD=/path/to/mpi/used/by/executable/lib/libfmpich.so:/home/carns/darshan-install/lib/libdarshan.so
234
----
235

236 237 238 239 240 241 242 243 244 245
[NOTE]
The full path to the libfmpich.so library can be omitted if the rpath
variable points to the correct path.  Be careful to check the rpath of the
darshan library and the executable before using this configuration, however.
They may provide conflicting paths.  Ideally the rpath to the  MPI library
would *not* be set by the darshan library, but would instead be specified
exclusively by the executable itself.  You can check the rpath of the
darshan library by running `objdump -x
/home/carns/darshan-install/lib/libdarshan.so |grep RPATH`.

246 247
== Darshan installation recipes

Philip Carns's avatar
Philip Carns committed
248
The following recipes provide examples for prominent HPC systems.
Philip Carns's avatar
Philip Carns committed
249
These are intended to be used as a starting point.  You will most likely have to adjust paths and options to
250 251
reflect the specifics of your system.

252
=== IBM Blue Gene (BG/P or BG/Q)
253

254
IBM Blue Gene systems produces static executables by default, uses a
255 256 257 258 259 260 261 262 263
different architecture for login and compute nodes, and uses an MPI
environment based on MPICH.

The following example shows how to configure Darshan on a BG/P system:

----
./configure --with-mem-align=16 \
 --with-log-path=/home/carns/working/darshan/releases/logs \
 --prefix=/home/carns/working/darshan/install --with-jobid-env=COBALT_JOBID \
264
 --with-zlib=/soft/apps/zlib-1.2.3/ \
265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281
 --host=powerpc-bgp-linux CC=/bgsys/drivers/ppcfloor/comm/default/bin/mpicc 
----

.Rationale
[NOTE]
====
The memory alignment is set to 16 not because that is the proper alignment
for the BG/P CPU architecture, but because that is the optimal alignment for
the network transport used between compute nodes and I/O nodes in the
system.  The jobid environment variable is set to `COBALT_JOBID` in this
case for use with the Cobalt scheduler, but other BG/P systems may use
different schedulers.  The `--with-zlib` argument is used to point to a
version of zlib that has been compiled for use on the compute nodes rather
than the login node.  The `--host` argument is used to force cross-compilation
of Darshan.  The `CC` variable is set to point to a stock MPI compiler.
====

282 283 284 285 286 287 288 289 290 291 292 293 294 295 296
Once Darshan has been installed, you can use one of the static
instrumentation methods described earlier in this document.  If you
use the profiling configuration file method, then please note that the
Darshan installation includes profiling configuration files that have been
adapted specifically for the Blue Gene environment.  Set the following
environment variables to enable them, and then use your normal compiler
scripts.  This method is compatible with both GNU and IBM compilers.

Blue Gene profiling configuration example:
----
export MPICC_PROFILE=$DARSHAN_PREFIX/share/mpi-profile/darshan-bg-cc
export MPICXX_PROFILE=$DARSHAN_PREFIX/share/mpi-profile/darshan-bg-cxx
export MPICF77_PROFILE=$DARSHAN_PREFIX/share/mpi-profile/darshan-bg-f
export MPICF90_PROFILE=$DARSHAN_PREFIX/share/mpi-profile/darshan-bg-f
----
297

298
=== Cray platforms (XE, XC, or similar)
299

300 301 302 303 304 305 306
The Cray programming environment produces static executables by default,
which means that Darshan instrumentation must be inserted at compile
time.  This can be accomplished by loading a software module that sets
appropriate environment variables to modify the Cray compiler script link
behavior.  This section describes how to compile and install Darshan,
as well as how to use a software module to enable and disable Darshan
instrumentation.
307 308 309 310 311 312

==== Building and installing Darshan

Please set your environment to use the GNU programming environment before
configuring or compiling Darshan.  Although Darshan can be built with a
variety of compilers, the GNU compilers are recommended because it will
313 314 315 316 317
produce a Darshan library that is interoperable with the widest range
of compmilers and linkers.  On most Cray systems you can enable the GNU
programming environment with a command similar to "module swap PrgEnv-pgi
PrgEnv-gnu".  Please see your site documentation for information about
how to switch programming environments.
318 319

The following example shows how to configure and build Darshan on a Cray
320
system using either the GNU programming environment.  Adjust the 
321 322
--with-log-path and --prefix arguments to point to the desired log file path 
and installation path, respectively.
323 324

----
325
module swap PrgEnv-pgi PrgEnv-gnu
326
./configure --with-mem-align=8 \
327 328
 --with-log-path=/shared-file-system/darshan-logs \
 --prefix=/soft/darshan-2.2.3 \
329
 --with-jobid-env=PBS_JOBID --disable-cuserid CC=cc
330 331
make install
module swap PrgEnv-gnu PrgEnv-pgi
332 333 334 335 336 337 338
----

.Rationale
[NOTE]
====
The job ID is set to `PBS_JOBID` for use with a Torque or PBS based scheduler.
The `CC` variable is configured to point the standard MPI compiler.
Philip Carns's avatar
Philip Carns committed
339 340 341 342 343 344 345 346

The --disable-cuserid argument is used to prevent Darshan from attempting to
use the cuserid() function to retrieve the user name associated with a job.
Darshan automatically falls back to other methods if this function fails,
but on some Cray environments (notably the Beagle XE6 system as of March 2012)
the cuserid() call triggers a segmentation fault.  With this option set,
Darshan will typically use the LOGNAME environment variable to determine a
userid.
347 348
====

349 350 351
As in any Darshan installation, the darshan-mk-log-dirs.pl script can then be 
used to create the appropriate directory hierarchy for storing Darshan log 
files in the --with-log-path directory.
Philip Carns's avatar
Philip Carns committed
352

353 354 355 356 357
Note that Darshan is not currently capable of detecting the stripe size
(and therefore the Darshan FILE_ALIGNMENT value) on Lustre file systems.
If a Lustre file system is detected, then Darshan assumes an optimal
file alignment of 1 MiB.

358
==== Enabling Darshan instrumentation 
359

360 361
Darshan will automatically install example software module files in the
following locations (depending on how you specified the --prefix option in
362
the previous section):
Philip Carns's avatar
Philip Carns committed
363

364
----
365
/soft/darshan-2.2.3/share/craype-1.x/modulefiles/darshan
366
/soft/darshan-2.2.3/share/craype-2.x/modulefiles/darshan
367
----
Philip Carns's avatar
Philip Carns committed
368

369 370
Select the one that is appropriate for your Cray programming environment
(see the version number of the craype module in `module list`).
Philip Carns's avatar
Philip Carns committed
371

372 373 374 375 376 377 378 379 380 381 382 383 384
If you are using the Cray Programming Environment version 1.x, then you
must modify the corresponding modulefile before using it.  Please see
the comments at the end of the file and choose an environment variable
method that is appropriate for your system.  If this is not done, then
the compiler may fail to link some applications when the Darshan module
is loaded.

If you are using the Cray Programming Environment version 2.x then you can
likely use the modulefile as is.  Note that it pulls most of its
configuration from the lib/pkgconfig/darshan-runtime.pc file installed with
Darshan.

The modulefile that you select can be copied to a system location, or the
385 386
install location can be added to your local module path with the following
command:
Philip Carns's avatar
Philip Carns committed
387

388
----
389
module use /soft/darshan-2.2.3/share/craype-<VERSION>/modulefiles
390
----
Philip Carns's avatar
Philip Carns committed
391

392 393
From this point, Darshan instrumenation can be enabled for all future
application compilations by running "module load darshan".
394 395 396 397 398 399 400 401 402 403 404 405 406 407 408 409 410 411 412 413 414 415 416 417 418 419 420 421 422 423 424 425

=== Linux clusters using Intel MPI 

Most Intel MPI installations produce dynamic executables by default.  To
configure Darshan in this environment you can use the following example:

----
./configure --with-mem-align=8 --with-log-path=/darshan-logs --with-jobid-env=PBS_JOBID CC=mpicc
----

.Rationale
[NOTE]
====
There is nothing unusual in this configuration except that you should use
the underlying GNU compilers rather than the Intel ICC compilers to compile
Darshan itself.
====

You can use the `LD_PRELOAD` method described earlier in this document to
instrument executables compiled with the Intel MPI compiler scripts.  This
method has been briefly tested using both GNU and Intel compilers.

.Caveat
[NOTE]
====
Darshan is only known to work with C and C++ executables generated by the
Intel MPI suite.  Darshan will not produce instrumentation for Fortran
executables.  For more details please check this Intel forum discussion:

http://software.intel.com/en-us/forums/showthread.php?t=103447&o=a&s=lr
====

426
=== Linux clusters using MPICH 
427

428 429 430 431 432 433 434
Follow the generic instructions provided at the top of this document.  For MPICH versions 3.1 and
later, MPICH uses shared libraries by default, so you may need to consider the dynamic linking
instrumentation approach.  

The static linking method can be used if MPICH is configured to use static
linking by default, or if you are using a version prior to 3.1.
The only modification is to make sure that the `CC` used for compilation is
435 436 437
based on a GNU compiler.  Once Darshan has been installed, it should be
capable of instrumenting executables built with GNU, Intel, and PGI
compilers.
Philip Carns's avatar
Philip Carns committed
438

439 440 441 442 443 444 445 446 447 448 449 450 451
[NOTE]
Darshan is not capable of instrumenting Fortran applications build with MPICH versions 3.1.1, 3.1.2,
or 3.1.3 due to a library symbol name compatibility issue.  Consider using a newer version of
MPICH if you wish to instrument Fortran applications.  Please see
http://trac.mpich.org/projects/mpich/ticket/2209 for more details.

[NOTE]
MPICH versions 3.1, 3.1.1, 3.1.2, and 3.1.3 may produce link-time errors when building static
executables (i.e. using the -static option) if MPICH is built with shared library support.
Please see http://trac.mpich.org/projects/mpich/ticket/2190 for more details.  The workaround if you
wish to use static linking is to configure MPICH with `--enable-shared=no --enable-static=yes` to
force it to use static MPI libraries with correct dependencies.

452 453 454 455 456 457 458 459 460 461 462 463 464
=== Linux clusters using Open MPI

Follow the generic instructions provided at the top of this document for
compilation, and make sure that the `CC` used for compilation is based on a
GNU compiler.

Open MPI typically produces dynamically linked executables by default, which
means that you should use the `LD_PRELOAD` method to instrument executables
that have been built with Open MPI.  Darshan is only compatible with Open
MPI 1.6.4 and newer.  For more details on why Darshan is not compatible with
older versions of Open MPI, please refer to the following mailing list discussion:

http://www.open-mpi.org/community/lists/devel/2013/01/11907.php
465 466 467 468 469 470 471 472 473

== Runtime environment variables

The Darshan library honors the following environment variables to modify
behavior at runtime:

* DARSHAN_DISABLE: disables Darshan instrumentation
* DARSHAN_INTERNAL_TIMING: enables internal instrumentation that will print the time required to startup and shutdown Darshan to stderr at run time.
* DARSHAN_LOGHINTS: specifies the MPI-IO hints to use when storing the Darshan output file.  The format is a semicolon-delimited list of key=value pairs, for example: hint1=value1;hint2=value2
474
* DARSHAN_MEMALIGN: specifies a value for system memory alignment
475
* DARSHAN_JOBID: specifies the name of the environment variable to use for the job identifier, such as PBS_JOBID
476
* DARSHAN_DISABLE_SHARED_REDUCTION: disables the step in Darshan aggregation in which files that were accessed by all ranks are collapsed into a single cumulative file record at rank 0.  This option retains more per-process information at the expense of creating larger log files. Note that it is up to individual instrumentation module implementations whether this environment variable is actually honored.
477
* DARSHAN_LOGPATH: specifies the path to write Darshan log files to. Note that this directory needs to be formatted using the darshan-mk-log-dirs script.
478
* DARSHAN_LOGFILE: specifies the path (directory + Darshan log file name) to write the output Darshan log to. This overrides the default Darshan behavior of automatically generating a log file name and adding it to a log file directory formatted using darshan-mk-log-dirs script.
479
* DARSHAN_MODMEM: specifies the maximum amount of memory (in MiB) a Darshan instrumentation module can consume at runtime.